134 134 sped2 smooth and linear operation feeling 4.5mm-travel push-push type SPED210203 2,000 japan export 2 1 1 2 poles positions non shorting changeover timing for pc board ? terminal type 1,12 0 280 400 minimum order unit pcs. alternate operation sped220200 product no. product line pc board connector mounting method 4.5 total travel mm 1 2 drawing no. typical specifications items specifications rating resistive load 1a 14.5v dc contact resistance initial / after operating life 100m max. / 100m max. operating force 4.170.74n operating life with load 30,000 cycles 1a 14.5v dc circuit configuration 2-pole, 1-position 1-pole, 2-position style pc board mounting dimensions viewed from the mounting face side 15.58 ?3 2.85 3.55 2.65 8 4-1 ?4.8 1.05 14 16.8 2 11.65 0.8 9.5 18.3 8.3 26.7 turnover position 3.5 ?9.7 ?10 ?11.15 4.5 travel terminal no. c1 terminal no. c2 terminal no. 1 terminal no. 2 a dimensions unit:mm 15 2-2.1 2.2 ? 3.05 hole 2.65 8 4- ? 1.2 hole 11.65 ( t=1.6 ) no. 1 refer to p.138 for soldering conditions. product no. number of packages pcs. export package measurements mm 1 case / japan 1 case / export packing SPED210203 400 2,000 4 00270290 bulk product no. number of packages pcs. export package measurements mm 1 case / japan 1 case / export packing sped220200 280 1,12 0 555375223 packing specifications tray horizontal type vertical type detector slide push rotary power dual-in-line package type
135 135 sped24.5mm-travel push-push type factory setting for contact points can be either 1 or 2. note circuit diagram c1 c2 1 2 style dimensions unit:mm no. 2 6.75 8 ?4.8 ?10 14 16.8 6.1 9.5 turnover position 3.5 ?9.7 8.8 ?10 ?11.15 1.2 17.2 4.5 travel terminal no. c1 c2 terminal no. 2 terminal no. 1 horizontal type vertical type detector slide push rotary power dual-in-line package type
115 115 vertical type series vertical spef sped2 sped3 sped4 sped5 photo dimensions mm w 9.4 14 13 . 5 d 9 16 . 8 18 18 . 2 h 6.9 18 . 3 16 . 9 7 13 .1 18 travel mm 1. 5 total travel mm 2.7 4.5 3.8 number of poles 1 1 2 1 operating temperature range ?40 to 85 ?40 to 95 automotive use life cycle rating max. resistive load 1a 14 . 5 v d c 2 a 14 . 5 v d c rating min. resistive load 50a 3v d c durability operating life without load operating life with load at max. rated load 30,000 cycles 100m max. electrical performance initial contact resistance 10 0 m m a x . insulation resistance 3 m m i n . 10 0 v d c 3m min. 500v dc voltage proof 10 0 v a c f o r 1m i n u t e mechanical performance terminal strength wire strength 30n actuator strength operating direction 90n 98n 90n 98n pulling direction 30n environmental performance cold ?40 96h dry heat 85 96h 85 96h (connector type) 105 192h (dip type) 10 5 19 2 h damp heat 40, 9 0 to 95%rh 96h page 13 2 13 4 13 6 push switches soldering conditions ??????????????????????????????????????????????? 138 push switches cautions ????????????????????????????????????????????????????? 139 note indicates applicability to all products in the series. horizontal type detector slide push rotary power dual-in-line package type
138 138 horizontal type vertical type soldering time speh series series example of reflow soldering condition 1. heating method: double heating method with infrared heater. 2. temperature measurement: thermocouple 0.1 to 0.2 ca (k) or cc (t) at soldering portion (copper foil surface). a heat resisting tape should be used for fixed measurement. 3. temperature profile 300 200 100 a max. b e d time (s) c pre-heating f max. room temperature temperature (?c ) 1. the condition mentioned above is the temperature on the mounting surface of a pc board. there are cases where the pc board's temperature greatly differs from that of the switch, depending on the pc board's material, size, thickness, etc. the above-stated conditions shall also apply to switch surface temp eratures. 2. soldering conditions differ depending on reflow soldering machines. pri or verification of soldering condition is highly recommended. notes 260 seriesreflow type 230 40 18 0 15 0 12 0 speg spej spef a 3s max. b cs d e fs 10 1s soldering temperature duration of immersion preheating temperature preheating time sppj2, spph1, sped2, sped4, spef spuj, spph2, spph4 spun sppj3 10 0 m a x . 60s max. 2605 5 1s 10 0 m a x . 60s max. 2605 10 1s 2605 5 1s 2605 items dip soldering reference for dip soldering (for pc board terminal types) 3 0 0 10 spuj 3 +1/ 0 s 350 max. speh , spph2 speg, spef spej sped2, sped4 sppj3, sppj2, spun, spph4, spph1 3 5 0 10 3 +1/ 0 s 3 5 0 10 30.5s 3 5 0 10 4s max. 3505 3s max. 3s max. soldering temperature reference for hand soldering for pc board??m push switches soldering conditions detector slide push rotary power dual-in-line package type
|
